+86 0371 8654 9132

used foundry sand in concrete

(PDF) Used Foundry Sand in Cement Mortars and Concrete ...

Foundry sand can be used in concrete to improve its strength and other durability factors. Foundry Sand can be used as a partial replacement of cement or as a partial

USE OF USED FOUNDRY SAND IN CONCRETE: A STATE

2019-4-21 · durability properties of the conventional cementitious concrete due to the addition or replacement of fine sand with used foundry sand in different proportions. However in couple of cases such addition has reported reduction in the values of properties. From the review of past research works it could be concluded that utilizing the used foundry sand holds a great potential towards the development of environment friendly and sustainable cementitious concretes.

(PDF) USE OF USED FOUNDRY SAND IN CONCRETE: A STATE

At 28-day age, concrete containing used foundry sand showed about 20-30% lower values than concrete without used foundry sand. But concrete containing 25% and 35% clean/new foundry sand

USE OF USED FOUNDRY SAND IN CONCRETE: A STATE OF

However in couple of cases such addition has reported reduction in the values of properties. From the review of past research works it could be concluded that utilizing the used foundry sand holds a great potential towards the development of environment friendly and sustainable cementitious concretes.

Utilization of Used Foundry Sand in Concrete | Journal of ...

At 28‐day age, concrete containing used foundry sand showed about 20–30% lower values than concrete without used foundry sand. But concrete containing 25% and 35% clean/new foundry sand gave almost the same compressive strength as that of the control mix.

Used Foundry Sand in Cement Mortars and Concrete Production

Used foundry sands represent the highest amount of solid wastes generated by foundries. Classified by European Union regulations as non hazardous waste, they represent a relevant source to be reused in several industrial sectors, in building construction primarily.

(PDF) UTILIZATION OF USED FOUNDRY SAND IN CONCRETE ...

This research was conducted to investigate the performance of fresh and hardened concrete containing discarded foundry sands in place of fine aggregate. A control concrete mix was proportioned to achieve a 28-day compressive strength of 38 MPa (5,500

Waste foundry sand in concrete: A review - ScienceDirect

2017-12-15 · Waste foundry sand, a by-product of ferrous and non ferrous metal casting industries is one such promising material which can be used as an alternative to natural sand in concrete. In last few decades, several studies have been conducted to investigate the effect of addition of waste foundry sand as partial and complete replacement of regular sand in concrete.

Usage of Waste Foundry Sand in Concrete

2019-1-24 · Foundry sand is basically fine aggregate. It can be used in many of the same ways as natural or manufactured sands. This includes many civil engineering applications such as embankments, flowable fill, hot mix asphalt (HMA) and portland cement concrete (PCC). Foundry sands have also been used extensively agriculturally as topsoil.

Using Foundry Waste Materials in Concrete for a More ...

2020-9-4 · have discovered that it can be used in concrete. Foundry waste can consist of many products such as spent foundry sand, slag, ash, refractory, coagulant, baghouse dust, pattern shop waste, and debris [1-4]. Of this waste a large percentage consists of spent foundry sand (SFS) from casting molds and slag from smelting of iron ore.

Utilization of Used Foundry Sand in Concrete | Journal of ...

Other concrete mixes were proportioned to replace 25% and 35% by weight of regular concrete sand with clean/new foundry sand and used foundry sand. Concrete performance was evaluated with respect to compressive strength, tensile strength, and modulus of elasticity. At 28‐day age, concrete containing used foundry sand showed about 20–30% ...

UTILIZATION OF USED FOUNDRY SAND IN CONCRETE

The details are described of the study in which a control concrete mix was proportioned to achieve a 28-day compressive strength of 38 MPa, and other mixes were proportioned to replace 25% and 35% by weight of regular concrete sand with clean, new foundry sand, and used foundry sand. At 28-day age, concrete containing used foundry sand showed ...

(PDF) UTILIZATION OF USED FOUNDRY SAND IN CONCRETE ...

This research was conducted to investigate the performance of fresh and hardened concrete containing discarded foundry sands in place of fine aggregate. A control concrete mix was proportioned to achieve a 28-day compressive strength of 38 MPa (5,500

Usage of Waste Foundry Sand in Concrete

2019-1-24 · Foundry sand is basically fine aggregate. It can be used in many of the same ways as natural or manufactured sands. This includes many civil engineering applications such as embankments, flowable fill, hot mix asphalt (HMA) and portland cement concrete (PCC). Foundry sands have also been used extensively agriculturally as topsoil.

Benificial Reuse of Waste Foundry Sand in Concrete

2021-6-4 · foundry sand and used foundry sand. Concrete performance was evaluated with respect to compressive strength, tensile strength, and modulus of elasticity. At 28-day age, concrete containing used foundry sand showed about 20-30% lower values than concrete without used foundry sand. But concrete containing25% and 35% clean/new foundry sand gave ...

A Study on Utilization of Used Foundry Sand:

2017-6-3 · Use of used foundry sand in different engineering applications can solve the problem of disposal of used foundry sand and other functions. Foundry sand exists primarily of silica sand, coated with a thin film of burnt carbon, residual and dust. To enhance the strength and other durability factors foundry sand can be used in concrete.

Using Foundry Waste Materials in Concrete for a More ...

2020-9-4 · cement was replaced in two percentages, with used-foundry sand and fly ash respectively. The results showed an improvement on strength and durability. In the pre-cast molded concrete, the average compressive strength was 32% higher than the control samples. Bikas et al. [9] incorporated used foundry sand in asphalt concrete with 4%, 7%, 10%, 14 ...

Mechanical Properties of Concrete Incorparating used

2019-1-29 · sand so foundry sand can be safely used in concrete for durability and strength purposes. KEY WORDS: Foundry sand, Compressive strength I.INTRODUCTION 1.1 General The physical and chemical characteristics of foundry sand will depend in great part on the type of casting process and the industry sector from which it originates.

Experimental Investigation of Foundry Sand in Concrete – IJERT

2019-4-29 · Based on the results, The replacement of natural sand with used foundry sand up to 30 % is desirable. as it is cost effective, reduce the amount of fine aggregate. Use of waste foundry sand in concrete reduces the production of waste through metal industries; it

Waste foundry sand in concrete: A review - ScienceDirect

Waste foundry sand, a by-product of ferrous and non ferrous metal casting industries is one such promising material which can be used as an alternative to natural sand in concrete. In last few decades, several studies have been conducted to investigate the effect of addition of waste foundry sand as partial and complete replacement of regular ...

Utilization of Used Foundry Sand in Concrete | Journal of ...

Other concrete mixes were proportioned to replace 25% and 35% by weight of regular concrete sand with clean/new foundry sand and used foundry sand. Concrete performance was evaluated with respect to compressive strength, tensile strength, and modulus of elasticity. At 28‐day age, concrete containing used foundry sand showed about 20–30% ...

CiteSeerX — USE OF USED FOUNDRY SAND IN CONCRETE:

CiteSeerX - Document Details (Isaac Councill, Lee Giles, Pradeep Teregowda): This state of art review represents the development in the field of utilization of used foundry sand in cementitious concrete. The paper reviews the utilization of foundry sand as the concrete constituent and the noticeable and important findings from the experimental works of various researchers.

UTILIZATION OF USED FOUNDRY SAND IN CONCRETE

The details are described of the study in which a control concrete mix was proportioned to achieve a 28-day compressive strength of 38 MPa, and other mixes were proportioned to replace 25% and 35% by weight of regular concrete sand with clean, new foundry sand, and used foundry sand. At 28-day age, concrete containing used foundry sand showed ...

[PDF] Used Foundry Sand in Cement Mortars and Concrete ...

Used foundry sands represent the highest amount of solid wastes generated by foundries. Classified by European Union regulations as non hazardous waste, they represent a relevant source to be reused in several industrial sectors, in building construction primarily. In present paper, the properties of mortars and concretes containing different dosages of used foundry sand (UFS) as partial ...

Methodology to evaluate used foundry sand as concrete ...

2008-6-5 · Methodology to evaluate used foundry sand as concrete aggregate Sbrighi Neto, C.;Tango, C.E.S.; Lotti, F.; Quarcioni, V.A. IPT Technological Research Institute of Sao Paula State - Brazil Abstract Nowadays used foundry sand becomes, more and more, an environmental problem because it is not easy to f’lnd a safety way to dispose it.

Utilization of Used Foundry sand and Hypo sludge in ...

2018-2-15 · Sohail et al. (2013) studied that foundry sand has effectively use to other industries. From the experimental study, result shows that Waste Foundry Sand can be effectively used as a replacement of natural sand in concrete. The maximum compressive strength was achieved at 50% replacement of fine aggregate with waste foundry sand.

Performance of spent garnet sand and used foundry sand as ...

2021-6-21 · In the current study, used foundry sand (UFS) and spent garnet sand (SGS) are used as a partial and full replacement to sand in concrete production. Design/methodology/approach The objective of the work is to develop non-conventional concrete by replacing river sand with a combination of UFS (constant 20Wt.% replacement) and SGS at various ...

Partial Replacement of Fine Aggregate by Used Foundry

2019-4-11 · by foundry sand in 10, 20, 30 & 40% by weight in concrete. From their test they concluded that Maximum compressive strength is obtained at 30% replacement and then decreases. By Tarun R Naik et al., [10] They investigated on the topic of ‘Utilization of Used Foundry Sand in Concrete’. Here they tested the values of the

SELF COMPACTING CONCRETE USING RED MUD AND

2019-4-21 · Natural river sand with maximum size of 4.75mm was used in this study. The specific gravity was found to be 2.64. replaced with used foundry sand (UFS). 2.1.5 Used Foundry Sand Foundry sand is a byproduct of ferrous and non-ferrous metal casting industries. Foundries successfully recycle and reuse the sand many times in the foundry.

Engineering properties of concrete with partial ...

One such industrial solid waste is Used Foundry Sand (UFS). On the other hand, fine aggregates involved in the concrete are generally river sand, which is scarce, high cost and excavation of the river sand that promote environmental degradation. So, there is an urge to find some alternative solution to dispose UFS and to limit the use of river ...